|
Good buy. First time working with the bits today and well satisfied, as usual, with the Freud products. Very sharp and smooth. Rebuilding from Hurricane and getting to use many of the new tools and these bits are well within the five star range for my money. You may pay a little more for the name, but the quality is there.
I have noticed no wobble in any of the bits and other than the sharpening problem have had no trouble with this set. They are usually ready to go out of the box. I examined the rest of the bits and they looked the same. This time the results were what I had hoped for.The bit cut thru the Padauk very nicely and left a nice clean hole. Cutting the last hole was as easy as cutting the first. I work with a lot of hardwoods and you have to be careful about the pressure you use with HSS bits, so you don't burn your workpiece or overheat your bit. I recieved this set as a gift and even though I already have these size's I was pretty excited to get a set of carbide bits.
I chucked up the 3/8 bit to bore some holes for decorative plugs and noticed that the bit was not cutting a very clean hole, seemed like I had to apply too much pressure also. I pulled it out of the drill press and upon examining the cutting edge, I noticed it did not have that bright, shiney edge you normally associate with a sharp tool. I love Freud cutters and saw blades. So $30 and an hour later I was on my way home with sharp bits. Put the 3/8 back in the drill press and tried again. I cut another 19 holes and each was excellent. I rated it 4 stars because of the sharpening problem. These are the first Freud cutter's I have had that were'nt sharp out of the box, so I won't let it influence my love of Freud blades and cutters in the future.
I have a set of Freud HSS Forstner bits, and they are very good. I do think my HSS set does a little better job in soft wood and plywood, but it is a close call. So I carried them down to the local saw shop where I get all my blades and cutters sharpened and ask them to take a look at the bits. Their opinion was that the bits were very dull, looked like the last two steps in sharpening them had been overlooked. Wish I could afford some larger ones in carbide.3"-31/2" would be nice for clock making. Still recommend Freud blades and cutters.
If I had to choose between the Freud carbide set and the Freud steel set, I would probably go with the steel, because it has 9 more bits. Instead I went with the 1-1/4" Freud steel forstner bit.
I have had very good results working with soft woods on my small drill press. The bits are very straight compared to the junky Irwin bits I got at Home Depot.
I have been using the bits for several months. I tried to purchase the Freud 1-1/4" carbide bit on Amazon, but they appear to no longer stock them.
The carbide bits are very sharp and cut a very true hole. The only problem I have with this set is that it is missing several handy sizes such as 7/8", 1-1/8" & 1-1/4".
The steel bit seems to work just as well as the carbide bits. Buying forstner bits individually can get very expensive.
My twenty year old hand sharpened steel bits produced better results. The surface of the workpiece had burrs where the bit first made contact and the interior of the hole showed a torn surface on the end grain side as opposed to a smooth cut.
The first was their 8 inch super dado set. This is my second experience with Freud cutting tools.
This forstner bit set produced disappointing results for the money. It had to be exchanged due toseveral chips in the carbide cutting edges.
The replacement has performed adequately. Overall the quality of the grinding on the carbide cutting tips and the body of the bit was uneven and poorly finished.
For the money I expected more and returned these bits.
Especially usefull for cutting shallow or flat bottom mortises, partial circles laid over the edge of your stock, and holes drilled at an angle to the surface. This set is worth the money for anyone serious about woodworking. These bits offer the most controlled cutting available when used with a drill press. The carbide edges offer much longer life between sharpenings. Also the 1 3/8" size is perfect for european cup hinges.
|
